By Kimberly Wallace
A furnace is a very important piece of equipment in any home. As such, it is important to ensure that it is working well at all times. Part of achieving this goal involves regularly cleaning and maintaining various parts of the equipment in good condition. When the equipment is not cleaned well, it starts to use more gas, oil, or electricity, leading to higher maintenance costs. It also becomes increasingly inefficient. When in need of oil furnace cleaning PA should be visited.
For several parts of the equipment to work efficiently, they have to be cleaned properly. The cleanliness of the entire equipment must be maintained, but more focus needs to be given to three main components. The three components are the filter system, the blower, and the heat exchanger. The equipment becomes less efficient if it is not cleaned for long, leading to accumulation of dirt.
Durability of the equipment is also increased when these components are kept clean. One has to have some knowledge before they start to clean the equipment. This is to ensure that the components are not damaged during the process of cleaning them. One should start by identifying the access panel of the equipment before they start to clean the named components. The panel is usually located on the outside of the equipment.
Most models have access panels located in the space between the blower and return-air duct. The duct is located on the upper side, then the access panel follows, while the blower comes last below it. As for the filter, it is located on the front side of the equipment. One ought to remove the front panel to access it. There may be a separate door on the filter. Prior to engaging in any of these activities, power supply should be switched off.
For the filter to be cleaned, it has to be removed from the compartment where it sits. Removing the filter from the compartment should be easy. In case there is difficulty in getting the filter out, one should be keen with how they proceed. One should inspect the filter for any dirt and if loose debris is present, it should be cleaned off.
Once all the loose dirt particles have been removed, tap water mixed with mild soap should be used to clean the remaining dirt. After all dirt has been removed, the filter should be rinsed using clean water and allowed to dry adequately. If there is any visible damage to the filter, it should be replaced if it is a disposable model.
The next step is to clean the blower assembly, which will require one to remove the entire front panel. There may be screws that hold the panel in place that need to be unscrewed. In case the panel is held in place by hinges instead of screws, they should be opened. One should slide the fan out of its compartment to be cleaned.
A wire may be used to connect the fan to other parts of the equipment. Primarily, the fan is attached on tracks. Clean water and mild soap should also be used to clean the fan and the blower assembly. It is best to use a toothbrush to clean fan blades and spaces between them. The heat exchanger is also cleaned using this procedure.
For several parts of the equipment to work efficiently, they have to be cleaned properly. The cleanliness of the entire equipment must be maintained, but more focus needs to be given to three main components. The three components are the filter system, the blower, and the heat exchanger. The equipment becomes less efficient if it is not cleaned for long, leading to accumulation of dirt.
Durability of the equipment is also increased when these components are kept clean. One has to have some knowledge before they start to clean the equipment. This is to ensure that the components are not damaged during the process of cleaning them. One should start by identifying the access panel of the equipment before they start to clean the named components. The panel is usually located on the outside of the equipment.
Most models have access panels located in the space between the blower and return-air duct. The duct is located on the upper side, then the access panel follows, while the blower comes last below it. As for the filter, it is located on the front side of the equipment. One ought to remove the front panel to access it. There may be a separate door on the filter. Prior to engaging in any of these activities, power supply should be switched off.
For the filter to be cleaned, it has to be removed from the compartment where it sits. Removing the filter from the compartment should be easy. In case there is difficulty in getting the filter out, one should be keen with how they proceed. One should inspect the filter for any dirt and if loose debris is present, it should be cleaned off.
Once all the loose dirt particles have been removed, tap water mixed with mild soap should be used to clean the remaining dirt. After all dirt has been removed, the filter should be rinsed using clean water and allowed to dry adequately. If there is any visible damage to the filter, it should be replaced if it is a disposable model.
The next step is to clean the blower assembly, which will require one to remove the entire front panel. There may be screws that hold the panel in place that need to be unscrewed. In case the panel is held in place by hinges instead of screws, they should be opened. One should slide the fan out of its compartment to be cleaned.
A wire may be used to connect the fan to other parts of the equipment. Primarily, the fan is attached on tracks. Clean water and mild soap should also be used to clean the fan and the blower assembly. It is best to use a toothbrush to clean fan blades and spaces between them. The heat exchanger is also cleaned using this procedure.
About the Author:
If you are searching for an oil furnace cleaning PA service, you can trust this source. Get all the specifics by clicking on this link http://www.capitolcityoil.com/Furnace-Cleanings.html.